Global Websites
Distribution Centers
DONN® Acoustical Suspension System Angle Moldings
-
The tools you need to help you install your suspension systems quickly and easily.They are available in multiple dimensions to match the aesthetic and performance requirements of any ceiling.
DONN Ceiling Suspension System Moldings are available in a variety of sizes, helping you achieve the aesthetic and performance characteristics you need, including seismic requirements and humidity resistance.
Angle Moldings are "L" shaped wall moldings used at the perimeter of a ceiling. Shadowline Moldings are useful for creating reveals at ceiling perimeters, while hiding imperfections in drywall partitions and bulkheads. US Channel Moldings are "U" shaped channels used at ceiling perimeters that can be used with (C8) wall spring clips to hold down perimeter ceiling tiles. F Moldings, when used with 1/2" or 5/8" SHEETROCK® Brandpanels, create ceiling "breaks" for soffits and changes in elevation.
| Title | Size | Add to Submittal |
|---|---|---|
| DONN® Suspension Systems Accessory Data Sheet - AC2396 [PDF] | 1,359 KB |
|
| Title | Size | Add to Submittal |
|---|---|---|
| DONN® Suspended Ceiling Installation Guide - R38 [PDF] | 815 KB |
|
| Title | Size | Add to Submittal |
|---|---|---|
| Ceiling Systems Catalog - SC2000 [PDF] | 42,936 KB |
|
| Ceiling Systems Catalog Supplement - SC2000A [PDF] | 29,752 KB |
|
| DONN® Suspension Systems System Catalog - SA904 [PDF] | 238 KB |
|
| Title | Size | Add to Submittal |
|---|---|---|
| DONN® Ceilings Warranty - SC2102 [PDF] | 92 KB |
|
Installation
Q: How do you take main tees apart without a tool?
A: Facing the main tee splice place your left hand near the left side of the splice and right hand near the right side of the splice. Using a shearing motion, push with your left hand and pull with your right hand. This disconnects the main tee splice. Be sure to straighten the end tabs before attempting to reconnect.
Q: How is the spacing of wire hangers determined for fire-rated assemblies?
A: All systems must be installed and tested in compliance with ASTM C636.
Q: How much force is required to insert a cross tee with a quick release clip?
A: It takes 12-14 pounds of force to install a cross tee.
Q: Do you mechanically attach the SHEETROCK ® Brand Liner Panels to the USG H studs?
A: No. The panels just slide into place.
Q: What gauge hanger wire is needed to install grid?
A: For residential installation 18-gauge wire is required. For commercial installation 12-gauge wire is required.
Q: How do you remove cross tees without a tool?
A: To remove a cross tee, push up on the main tee with your thumbs (where the cross tee is connected) and rotate it until the cross tee pops up and out of the slot.
Q: What is the best way to suspend a ceiling system beneath an existing grid system?
A: What is the best way to suspend a ceiling system beneath an existing grid system?
Q: How far apart should hanger wires be spaced when installing grid?
A: Hanger wires should be spaced between 4' and 6' depending on how much load the grid will carry. Hanger wires that are spaced closer allow the system to carry heavier loads.
Performance
Q: Which grid is the best grid to use in a Clean Room environment?
A: DONN ® CE is the best grid for a Clean Room environment.
Q: What is the standard warranty of grid?
A: Ten years. See complete warranty for details.
Q: What are the best grids to use in an area that is accessible to moisture?
A: DONN ® AX™ or ZXLA™.
Q: What is the warranty for a system, that uses USG tile and grid together?
A: There is a lifetime warranty on any ceiling system that is used in conjunction with our tile and grid. All grid is lifetime when used with USG tile, however not all tile is lifetime when used with USG grid. See complete warranty for details.
Technical
Q: How is the load test data collected for ceiling grid?
A: Load data and spans are based on simple span tests in accordance with ASTM C635, with a deflection limitation of L/360.
Q: When installing grid, what is the minimum clearance needed from the overhead structure?
A: Minimum clearance is 3", which allows ceiling tiles to be inserted and removed freely
Additional Resources
Quick Facts
- Fire Rated
- Fire Class A
- Colors: [Plated Chrome 066, Silver Satin 002, White, Plated Brass 065, Donn White 04, Flat Black 205, Flat White 050, Straw 143, High Gloss White, Parchment 103, Mist 053, Beige 142]
- Edge/Profile: [Angle Molding]
- Humidity Resistant
- 90% Recycled
